┌───────────────────────────────────────────────────────┐

│ M A T E R I A L S A F E T Y D A T A S H E E T │

└───────────────────────────────────────────────────────┘

┌─────────────────────────────────────────────────────────────────────────┐

│ SECTION 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION │

└─────────────────────────────────────────────────────────────────────────┘

MANUFACTURER: A.V.W INC.

24 HOUR EMERGENCY PHONE 800-424-9300

PRODUCT NAME: Max Professional™ MIST ADHESIVE

Revised: 04/22/08

│ SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS │

WT/WT %

ITEM ------------ CHEMICAL NAME ------------- CAS NUMBER LESS THAN

───────────────────────────────────────────────────────────────────────────

01 ISOHEXANE 107-83-5 25.0 %

02 PROPANE 74-98-6 15.0 %

03 DIMETHYL ETHER 115-10-6 15.0 %

04 ACETONE 67-64-1 15.0 %

05 CYCLOHEXANE 110-82-7 15.0 %

06 ETHANE, 1,1-DIFLUORO 75-37-6 10.0 %

07 N-PENTANE 109-66-0 5.0 %

---------------------- EXPOSURE LIMITS --------------------

ACGIH OSHA COMPANY

ITEM TLV-TWA TLV-STEL PEL-TWA PEL-CEILING TLV-TWA SKIN

01 500 ppm 1000 ppm N.E. N.E. N.E. NO

02 2500 PPM N.E. 1000 ppm N.E. N.E. NO

03 N.E. N.E. N.E. N.E. 1000 ppm NO

04 500 ppm 750 ppm 1000 ppm N.E. N.E. NO

05 100 ppm N.E. 300 ppm N.E. N.E. NO

06 N.E. N.E. N.E. N.E. 1000 ppm NO

07 600 ppm N.E. 1000 ppm N.E. N.E. NO

(See Section 16 for abbreviation legend)

│ SECTION 3 - HAZARDS IDENTIFICATION │

*** EMERGENCY OVERVIEW ***: Keep from reach of children. Do not puncture,

incinerate, or place aerosol product containers in compactors. Containers

(Continued on Page 2)

Page 2

│ SECTION 3 - HAZARDS IDENTIFICATION │

of this material may be hazardous when emptied since containers retain

product residues (vapor, liquid, and/or solid). All hazardprecautions

given must be observed. Do not flame cut, braze or use welding torch.

Intentional misuse by deliberately concentrating and inhaling this product

may be harmful or fatal.

EFFECTS OF OVEREXPOSURE - EYE CONTACT: Can cause severe irritation,

redness, tearing, blurred vision.

EFFECTS OF OVEREXPOSURE - SKIN CONTACT: Prolonged or repeated contact can

cause moderate irritation defatting, dermatitis.

EFFECTS OF OVEREXPOSURE - INHALATION: Excessive inhalation of vapors can

cause nasal and respiratory irritation, dizziness, weakness, fatigue,

nausea, headache, possible unconsciousness, and even asphyxiation.

Possible cardiac arrhythmias at high concentrations.

EFFECTS OF OVEREXPOSURE - INGESTION: No Information.

EFFECTS OF OVEREXPOSURE - CHRONIC HAZARDS: Overexposure to this material

(or its components) has apparently been found to cause the following

effects in laboratory animals: kidney damage, eye damage, liver damage,

PRIMARY ROUTE(S) OF ENTRY: SKIN CONTACT SKIN ABSORPTION INHALATION EYE

CONTACT

│ SECTION 4 - FIRST AID MEASURES │

FIRST AID - EYE CONTACT: Flush with large amounts of water, lifting upper

and lower lids occasionally, get medical attention.

FIRST AID - SKIN CONTACT: Thoroughly wash exposed area with soap and

water. Remove contaminated clothing. Launder contaminated clothing before

re-use. Get medical attention if irritation persists. Mineral oil, baby

oil, makeup remover, mineral spirits, or other similar mild solvent may be

used to remove the sticky resin residue left by the adhesive.

FIRST AID - INHALATION: Remove individual to fresh air. If breathing is

difficult, administer oxygen. Give artificial respiration if breathing has

stopped. Keep person warm and quiet. Get medical attention.

FIRST AID - INGESTION: Do not induce vomiting. Give two glasses of water

if conscious. Never give anything by mouth to an unconscious person. Get

immediate medical attention.

│ SECTION 5 - FIRE FIGHTING MEASURES │

FLASH POINT: -156 F LOWER EXPLOSIVE LIMIT: 1.0 %

(PENSKY-MARTENS C.C.) UPPER EXPLOSIVE LIMIT: 18.0 %

(Continued on Page 3)

Page 3

│ SECTION 5 - FIRE FIGHTING MEASURES │

AUTOIGNITION TEMPERATURE: N.D.

EXTINGUISHING MEDIA: CO2 DRY CHEMICAL FOAM WATER FOG

UNUSUAL FIRE AND EXPLOSION HAZARDS: Vapors are heavier than air and travel

along the ground or may be moved by ventilation and ignited by ignition

sources at locations distant from material handling point. For aerosol

products - exposure to temperatures over 130F may cause containers to burst

releasing highly flammable gas.

SPECIAL FIREFIGHTING PROCEDURES: Wear self-contained breathing apparatus

with a full facepiece operated in pressure-demand or other positive

pressure mode when fighting fires. Keep fire exposed containers cool with

water fog.

│ SECTION 6 - ACCIDENTAL RELEASE MEASURES │

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Eliminate

sources of ignition & ventilate area. Persons not properly equipped should

be excluded from area. Stop spill at source - prevent spreading. Avoid

inhalation of vapors. Avoid skin contact with liquid. Soak up on

absorbent material and place into proper container for disposal. Use

non-sparking scoops for flammable materials. Clean walking surfaces

thoroughly to reduce slipping hazard.

│ SECTION 7 - HANDLING AND STORAGE │

HANDLING: Containers of this material may be hazardous when emptied, since

containers retain product residues (vapor, liquid, and/or solid). All

hazard precautions given must be observed. Do not flame cut, braze or use

welding torch on containers. Intentional misuse by deliberately

concentrating and inhaling the vapors from this product may be harmful or

fatal.

STORAGE: Do not store above 120F. Do not store in direct sunlight. Keep

away from heat sources, open flame, pilot lights, sparks, and other sources

of ignition. Do not store above 120F. Do not store in direct sunlight.

│ SECTION 8 - EXPOSURE CONTROLS/PERSONAL PROTECTION │

ENGINEERING CONTROLS: Provide sufficient mechanical ventilation (general

and/or local exhaust) ventilation to maintain exposure below TLV(s).

RESPIRATORY PROTECTION: If work place exposure limits of product or any

component is exceeded, use a NIOSH/MSHA approved respirator. Consult your

safety equipment supplier for recommendations.

SKIN PROTECTION: Wear impervious gloves if method of use involves skin

(Continued on Page 4)

Page 4

│ SECTION 8 - EXPOSURE CONTROLS/PERSONAL PROTECTION │

contact with product. Consult your safety supply vendor for glove

recommendations.

EYE PROTECTION: Wear safety glasses at minimum, more extensive protection

may be necessary depending on how the product is to be used.

OTHER PROTECTIVE EQUIPMENT: Wear impervious clothing if bodily exposure is

anticipated. Consult your safety supply vendor for recommendations.

HYGIENIC PRACTICES: Wash hands before eating or smoking. Smoke in

designated areas only. Remove and launder clothing if contaminated.

│ SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES │

BOILING RANGE : -44 - 177 F VAPOR DENSITY : Is heavier than air

ODOR : MINT WHEN WET ODOR THRESHOLD : N.D.

APPEARANCE : WHITE LIQUID EVAPORATION RATE: Is faster than Butyl

SOLUBILITY IN H2O : NEGLIGIBLE Acetate

FREEZE POINT : N.D. SPECIFIC GRAVITY: 0.7084

VAPOR PRESSURE : N.D. pH @ 0.0 % : N.D.

PHYSICAL STATE : LIQUID VISCOSITY : N.D.

COEFFICIENT OF WATER/OIL DISTRIBUTION: N.D.

(See Section 16 for abbreviation legend)

│ SECTION 10 - STABILITY AND REACTIVITY │

CONDITIONS TO AVOID: Heat, sparks, welding arcs, open flame, pilot lights,

static electricity or other source of ignition.

INCOMPATIBILITY: oxidizing agents, acids, alkali, alkaline earth

metals, amines, reducing agents, strong oxidizers, Very strong acid,

caustic or oxidizing agents.

HAZARDOUS DECOMPOSITION PRODUCTS: hydrofluoric acid and possibly carbonyl

fluoride. carbon monoxide and carbon dioxide, various hydrocarbons,

sulfur dioxide, sulfur monoxide,

HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.

STABILITY: This product is stable under normal storage conditions.

│ SECTION 11 - TOXICOLOGICAL PROPERTIES │

No product or component toxicological information is available.

(Continued on Page 5)

Page 5

│ SECTION 12 - ECOLOGICAL INFORMATION │

ECOLOGICAL INFORMATION: No Information.

│ SECTION 13 - DISPOSAL CONSIDERATIONS │

DISPOSAL METHOD: Dispose of in accordance with all local, state and

federal regulations.

│ SECTION 14 - TRANSPORTATION INFORMATION │

DOT PROPER SHIPPING NAME: Aerosols

DOT TECHNICAL NAME:

DOT HAZARD CLASS: 2.1 HAZARD SUBCLASS: NONE

DOT UN/NA NUMBER: UN1950 PACKING GROUP: NONE RESP. GUIDE PAGE: 126

ADDITIONAL INFORMATION:: For domestic ground and air shipment this product

may be shipped as a Consumer Commodity ORM-D. Outer cartons must have the

ORM-D or ORM-D AIR designation. (our original cartons are preprinted with

the ORM-D designation for ground shipment)

│ SECTION 15 - REGULATORY INFORMATION │

U.S. FEDERAL REGULATIONS: AS FOLLOWS -

OSHA: Hazardous by definition of Hazard Communication Standard (29 CFR

1910.1200)

CERCLA - SARA HAZARD CATEGORY:

This product has been reviewed according to the EPA 'Hazard Categories'

promulgated under Sections 311 and 312 of the Superfund Amendment and

Reauthorization Act of 1986 (SARA Title III) and is considered, under

applicable definitions, to meet the following categories:

IMMEDIATE HEALTH HAZARD FIRE HAZARD PRESSURIZED GAS HAZARD

SARA SECTION 313:

This product contains the following substances subject to the reporting

requirements of Section 313 of Title III of the Superfund Amendments and

Reauthorization Act of 1986 and 40 CFR Part 372:

----------- CHEMICAL NAME ----------- CAS NUMBER WT/WT % IS LESS THAN

CYCLOHEXANE 110-82-7 15.0 %

TOXIC SUBSTANCES CONTROL ACT:

(Continued on Page 6)

Page 6

│ SECTION 15 - REGULATORY INFORMATION │

TOXIC SUBSTANCES CONTROL ACT:

This product contains the following chemical substances subject to the

reporting requirements of TSCA 12(B) if exported from the United States:

----------- CHEMICAL NAME ----------- CAS NUMBER

No information is available.

INTERNATIONAL REGULATIONS: AS FOLLOWS -

CANADIAN WHMIS: This MSDS has been prepared in compliance with Controlled

Product Regulations except for use of the 16 headings.

CANADIAN WHMIS CLASS: No information available.

: On June 30, 1993 the OSHA Z-1-A table was revoked and OSHA reverted back

to their prior exposure limits. The values on this MSDS reflect the roll

back to the prior values. Some states may continue to enforce the 1993

limits. On June 16, 1995 EPA announced in a final rule that acetone would

no longer be considered a VOC for air attainment standards.(it is now an

exempt compound) The VOC calculations on this MSDS are based on acetone

being an exempt compound. The June 16 rule also removed acetone from the

list of SARA 313 reportable chemicals.

│ SECTION 16 - OTHER INFORMATION │

HMIS RATINGS - HEALTH: 2 FLAMMABILITY: 4 REACTIVITY: 1

PREVIOUS MSDS REVISION DATE: 03/03/04

REASON FOR REVISION: NEW PRODUCT

VOLATILE BY WEIGHT: 82.8%

VOC CONTENT: 63.7 % BY WEIGHT, 454 GRAMS/LITER TOTAL PRODUCT,

544 GRAMS/LITER LESS WATER AND EXEMPT, 0.53 LBS/CAN

LEGEND: N.A. - Not Applicable, N.E. - Not Established,

N.D. - Not Determined